Top printed circuit board manufacturer

Printed circuit board provider with bstpcb.com? Most of our engineer and operators has more than ten years of experience in PCB industry, so we can produce special such as 20 OZ heavy copper board, 4 layers MCPCB, etc. At the same time, we purchased many advanced, art-of-state machines & devices for PCB manufacturing, checking, to improve the quality of our boards. See more info at ultra thin core pcb. The next layer is a thin copper foil, which is laminated to the board with heat and adhesive. On common, double sided PCBs, copper is applied to both sides of the substrate. In lower cost electronic gadgets the PCB may have copper on only one side. When we refer to a double sided or 2-layer board we are referring to the number of copper layers (2) in our lasagna. This can be as few as 1 layer or as many as 16 layers or more. The copper thickness can vary and is specified by weight, in ounces per square foot. The vast majority of PCBs have 1 ounce of copper per square foot but some PCBs that handle very high power may use 2 or 3 ounce copper. Each ounce per square translates to about 35 micrometers or 1.4 thousandths of an inch of thickness of copper.

Double sided flex circuits consists with double sided copper conductors and can be connected from both sides. It allows more complicated circuit designs, more components assembled. The major material used are copper foil, polyimide and coverlay. Adhesiveless stack up is popular for better dimensional stability, high temperature, thinner thickness. Dual access flexible circuit board refer to the flex circuit which can be accessed from both top and bottom side but only has only layer of conductor trace. Copper thickness 1OZ and coverlay 1mil, it similar with 1 layer FPC and opposite side FFC. There’re coverlay openings on both sides of flex circuit so that there’re solderable PAD on both top and bottom sides, that is similar with double sided FPC, but dual access flex circuit board has different stack up because of only one copper trace, so no plating process is need to make plated through hole (PTH) to connect between top and bottom side, and trace layout is much more simple. Quality Policy: PCB Quality is the core of products. All of engineer & vital department guys has more than five years expenrience in PCB industry, we follow up the default PCB standard, as well as with clients’ special request.

In order to provide one-stop-services to customers, we can also provide FPC and Rigid-flex PCB Assembly service (also named SMT: Surface Mounting Technology). We can purchase all components from abroad or domestic market, and provide full products to you with short lead time. High Density Interconnects (HDI) board are defined as a board (PCB) with a higher wiring density per unit area than conventional printed circuit boards (PCB). They have finer lines and spaces (<100 µm), smaller vias (<150 µm) and capture pads (300, and higher connection pad density (>20 pads/cm2) than employed in conventional PCB technology. HDI board is used to reduce size and weight, as well as to enhance electrical performance.

The design, as well as the manufacture of flexible PCBs, is a very nimble job. Seemingly minor errors such as two metal traces not being insulated on a high-voltage board, for example, can result in an arc leading to the destruction of the circuit. Errors in manufacturing can come by way of wrong selection of materials, improper design, and other such factors that can result in the capability of the flexible PCB to bend and take the required shape. If the PCB tends to fall from a height or any other external forces such as frequent plugging and unplugging of the PCB, it can cause damage to your PCB. Unreliable and faulty components can damage the board in many ways. One of them is the fact that they are unable to protect the PCB from overheating.

According to different manufacturing method, current there’re three basic types for ceramic board: A) Thick Film Ceramic Board Thick Film Ceramic PCB: Using this technology, the thickness of conductor layer exceeds 10 micron, more thick than spurting technology. The conductor is silver or gold palladium, and was printed on ceramic substrate. More for Thick Film Ceramic PCB. B) DCB Ceramic Board DCB (Direct Copper Bonded) technology denotes a special process in which the copper foil and the core (Al2O3 or ALN), on one or both sides, are directly bonded under appropriate high temperature and pressure. Read additional information on bstpcb.com.

Metal Core PCB means the core (base) material for PCB is the metal, not the normal FR4/CEM1-3, etc. and currently the most common metal used for MCPCB manufacturer are Aluminum, Copper and steel alloy. Aluminum has good heat transferring and dissipation ability, but yet relatively cheaper; copper has even better performance but relatively more expensive, and steel can be divided into normal steel and stainless steel. It more rigid than both aluminum and copper, but thermal conductivity is lower than them too. People will choose their own base/core material according to their different application.