Several MIG welders advices

A few advices about welding equipment, MIG and TIG welders, plasma cutters. A welder is a long term investment where many find that they get what they pay for. While it is sometimes advisable to test the waters with a used model, picking the right machine the first time around can save a lot of headaches and cash in the long term. No one wants a used welder to fail in the middle of a big job or to discover that a used welder’s price can help make ends meet but the welder itself can’t make two pieces of metal meet. The best welder will complete every project that comes down the pike and minimizes limitations. This means that the most expensive welder is not always the best for each situation. However, the cheapest welding machine that can’t handle every job a welder hopes to accomplish fails to pay for itself in ways that make it worthwhile to review the possible options before investing in a welder.

Several welding equipment tricks: how to become a more skilled welder and how to choose the best welding equipment. For DCEN welding on steels, 1/16″ will work in the 20 to 100 amp rage as long as you prep it right. If you are using 20 amps, you will need a needle sharp point to get good crisp arc starts. At 100 amps, you might not want quite a needle sharp point or you might be putting a smidge of tungsten in the weld. You need a blunter taper. Some charts extend the range to 150 amps for 1/16, but I think that’s way too much. Why not just swap to a 3/32 at that amperage.? 3/32″ is good from about 65 – 200 amps. And 1/8″ 2% thoriated electrodes are good in the 85 – 300 amp range. ( Drop all these numbers by about 30% for A/C) Using helium mixed with the argon will also change the recommended currents because the arc is hotter with the same amps. These recommendations are from down and dirty experience and don’t come from a chart. Most charts I have seen tell you a 1/16 tungsten is good all the way to 150 amps…Please.

In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode. Looking for the best Welding Fume Extraction? We recommend Welding Supplies Direct & associated company TWS Direct Ltd is an online distributor of a wide variety of welding supplies, welding equipment and welding machine. We supply plasma cutters, MIG, TIG, ARC welding machines and support consumables to the UK, Europe and North America.

Argon is not the only shielding gas used for TIG welding: Shielding gasses for TIG welding Argon is not the only shielding gas used for TIG welding…just the most common and versatile. Argon will usually get the job done. But there are times when some helium mixed with argon makes a world of difference. Especially if you are using a small inverter TIG welder that is limited to around 200 amps. 100% Argon – is the most often used and coolest gas ..the best all around gas. 75% Argon/25% Helium – even 25% helium will make a big difference when welding aluminum that is thicker than .063″. Anything under .063″ thick and helium is unnecessary. 50/50 argon/helium—awesome for thick aluminum and magnesium 75% Helium/25% Argon – Awesome for thick aluminum castings… puddles really quick and welds cleaner than 100% argon. Also good for welding bronze and pure copper on DCEN.

MIG Welding Increases Welding Speed: In addition to welding aluminum and other softer metals, MIG-welding works faster, provides cleaner welds, and handles many different types of metals. The downside is its complexity. MIG Welders need direct currents, a steady stream of inert gas, and precise control of their torches. The amount of heat generated from MIG welding provides the deep penetration required for a strong weld, while also melting the feed wire rapidly enough to maintain a higher welding speed than other techniques. Given the inert gas required for MIG welding, keep in mind that this technique cannot be conducted in windy areas. The Right Stick Electrode Increases Welding Speed: There are three kinds of electrodes used for stick welding: fast-fill, fill-freeze, and fast-follow. While each electrode has its advantages, the fast-fill electrodes melt quickly and allow welders to work faster.

Before you start welding, make sure all of your connections are tight — from the front of the MIG gun to the power pin attaching it to the power source. Also be certain there is no spatter buildup on your consumables and that you have a ground cable as close to the workspace as possible. Whenever possible, hook the ground cable on the weldment. If that is not possible, hook it to a bench. But remember: The closer it is to the arc, the better. If you have a questionable ground, it can cause the gun to overheat, impacting contact tip life and weld quality. In addition, regularly clean any shavings from the welding wire or debris that collects on your consumable parts and in your liner using clean compressed air.

All welding requires the application of heat, which melts the metal being welded. With the TIG process, the heat comes from an electric arc that streams between the electrode in a hand-held torch and the metal being welded. The arc and molten metal are shielded by an inert gas, which protects the electrode and base metal from oxidizing. Filler rod is usually added to the puddle of molten metal as the weld progresses. The essence of making a good weld is heat control, which is governed by how you modulate the arc as it streams from the torch. Let’s look at this in detail. Source: https://www.weldingsuppliesdirect.co.uk/.